Welcome to visit Nide Corporation official website!
Products
Home > Products >Self-Balance Scooter Wheel Hub Motor Winding machine

Self-Balance Scooter Wheel Hub Motor Winding machine

Model number:ND-R2SW01H
Introduction:The automtaic wheel hub motor winding machine is suitable for self-balancing scooters, electric scooters, electric balance cars, small electric vehicles, two-wheeled electric vehicles.

Product video

  • Specification
  • Automatic Self-Balance Scooter Wheel Hub Motor Winding machine

     

    This brushless wheel hub motor winding machine is suitable for self-balancing scooter motor windings. It adopts flying fork winding technology and is equipped with two winding machine stations, which can wind 9 strands at the same time.

     

    The brushless wheel hub motor is built into the drive wheel. This structure not only reduces the overall weight of the self-balancing scooter, but also the motor is not easily damaged. The self-balancing scooter has obvious advantages in volume and weight, the overall mass is reduced, the energy transmission link and energy loss are reduced, and the motor generates less heat.

     

    Wheel hub winding machine application:

    Self-balancing scooters, electric scooters, electric balance cars, small electric vehicles, two-wheeled electric vehicles.

     

    Technical parameters:

    Product name: Automatic self-balancing scooter wheel motor winding machine
    Wheel motor Stator ID: 10-100mm
    Wheel motor Stator O.D: 80-310mm
    Wheel motor Stator stack length: 10-50mm
    Wire dia: 0.2-1.3mm
    Max. winding speed : 1200RPM
    Winding station: 2
    Winding method: Flyer Coil Winding
    Parallel winding wire number : 1-12
    Voltage : three phase 380V 50HZ , single phase 220V 50HZ
    Air pressure: 0.4-0.7 MPA
    Total power : <7KW
    Weight : about 750KG
    Dimension : 1100x1000x1700mm


    Picture Show:

    Self-Balance Scooter Wheel Hub Motor Winding machine.jpg

    Motor Winding machine.jpg

    Wheel Hub Motor Winding machine.jpg

     Hub BLDC Motor Winding machine.jpg

    Electric Scooter Wheel Hub Motor Winding machine.jpg

    Our in-wheel motor winding technology reduces starting current and back EMF, reducing energy losses. There are mainly single wire windings or multi-wire windings, depending on the needs of the in-wheel motor and its load and road conditions.

     

    Single wire winding

    Single-strand wire windings are suitable for mass production. Use mechanical winding to wind the enameled wire with a diameter of 0.7mm to 1.2mm for 10 to 20 turns, and try to make good use of the area in the slot without affecting the mechanical winding to control the speed of the hub motor body, which can improve the efficiency of the hub motor body. Controlled at around 83%.

     

    Stranded wire winding

    The multi-strand wire winding can achieve the best overall performance of the hub motor body. The winding is an enameled wire with a diameter of 0.3mm to 0.45mm, and 5 to 8 strands are wound for 5 to 10 turns. Using multi-strand wire winding, increase the starting current to 0.8A ~ 2.3A, which can increase part of the torque and remove the skin effect.


    About NIDE

    Nide is to provide different kinds of motor manufacturing machinery, including stand along machine, fully-auto complete line for armature and stator production, and the motor assembly line.We can supply the full range of motor components such as commutator, ball bearing, carbon brush, insulation paper, shaft, magnet, fan, motor cover,etc.We also provide technical support and consulting, project support and turn-key service for some motor manufacturing.

    motor manufacturing machine

    Our machine's application

    Our machines are mainly applied to induction motors, BLDC motor, universal motor, three phase motor, single phase motor, AC motor, DC motor, such as washing machine motor, air conditioner motor, pump motor, cooler motor, alternator motor, fan motor, ceiling fan motor, compressor motor, power tool motor, vacuum cleaner motor, mixer motor,  series motor, electrical car motor, wheel hub motor, electric toothbrush motor, hair dryer motor, electric shaver motor,etc.


    Contact us

    Motor Parts Department

    Manager: Annie    

    Phone/Whatsapp/Wechat : 0086-13738869026 

    Email : emarketing@nide-group.com;


    Motor Manufacturing Machine Department

    Manager:Herbert Zhang

    Phone/Whatsapp/Wechat : 0086-15067409300

    Email : emarketing@nide-group.com; marketing8@nide-group.com;


    Address:14-5, East Kemao Center, No.100 Xiangyun Road, Hi-tech District, Ningbo 315040, China

    SNS